Sanus Systems Digital Camera WFA37 User Guide

Assembly Instructions for Model: WFA37  
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is  
constructed of real hardwood and resonance dampening MDF.  
Safety Warning: If you do not understand these directions, or have any doubts about the  
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or  
customer service representatives can quickly assist you with installation questions and missing  
or damaged parts. Replacement parts for products purchased through authorized dealers will be  
shipped directly to you. Never use defective parts. Improper installation may cause damage or  
serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus  
Systems. Sanus Systems can not be liable for damage or injury caused by incorrect assembly, or  
incorrect use. Please call Sanus Systems before returning products to the point of purchase.  
Required Tools: Phillips screw driver  
Supplied Parts and Hardware: Some parts may be pre-assembled together*  
Hardware: Shown as actual size  
(8) Cam Pin - a  
(4) Dowel Pin - c  
(8) Dowel - d  
(16) Shelf Pin - e  
(8) Cam - b  
(4) Wood Screw - f  
(4) Spacer - g  
(2) Phillips Bolt - h  
(1) Door Handle - i*  
(4) Hinge Screw - j  
(4) Hinge Plate Screw - k  
Parts: Not Shown as actual size  
(2) Hinge - l*  
(2) Hinge Plate - m*  
(2) Back Stretcher - p  
(2) Front Stretcher - o  
(1) Top - n  
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05  
 
Step 2: Prepare Stretchers  
Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the  
Stretchers. See Diagram 2 for assistance.  
Diagram 2  
Detailed View  
o
a
arrow  
p
Step 3: Add Stretchers  
Add the Front and Back Stretchers (o,p) to the Side Panel (s), by aligning the Cam Pin (a) with the hole which the Cams (b) point to  
and the Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest  
to the Side Panel in a clockwise motion until the stretchers are secured. Note: Front stretchers attach to the same side as the  
hinge holes are on.  
Diagram 3  
Detailed View  
s
d
b
a
hinge  
holes  
p
 
Step 4: Add Side Panel  
Press fit the Side Panel (t) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel  
(d) fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured. Note: Make sure the hinge  
holes on the Side Panel are on the same side as the Front Stretchers.  
Diagram 4  
Detailed View  
p
b
o
t
a
hinge  
holes  
Step 5: Add Shelf Pins and Bottom Shelf  
Thread the Shelf Pins (e) into the bottom hole in the line of holes in each Side Panel (s,t). Tighten all four Shelf Pins with a Phillips screw  
driver. Add the Bottom Shelf (q) by inserting it into the assembly and press fit it onto the Shelf Pins. Make sure the Bottom Shelf is flush  
against the Front Stretcher (o). If there is a gap in front, the shelf may be backward. See Diagram 5 for assistance.  
Note: Diagram 5 is a Back View.  
Diagram 5  
Detailed View  
e
s
q
q
t
 
Step 6: Add Top  
Gently tap a Dowel Pin (c) into the holes on the top of each Side Panel (s,t). Slide a Spacer (g) over each Dowel Pin. Press fit the Top  
(n) so it fits onto the Dowel Pins. See Diagram 6 for assistance.  
Diagram 6  
Detailed View  
n
c
g
s
t
t
Step 7: Add Door Handle  
Insert each Phillips Bolt (h) through the Door (v) and into the Door Handle (i). Tighten with a Phillips screw driver. See Diagram 7 for  
assistance. The Door Panels can be interchanged by removing and re-installing the plastic border from the perimeter of the Door’s back  
side.  
Diagram 7  
Detailed View  
i
h
v
 
Step 8: Add Hinge Assembly to Door  
Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (v). Tighten each with a Phillips screw driver. Repeat process  
until both Hinge Assemblies are secured.  
Diagram 8  
Detailed View  
v
m
j
l
Step 9: Door Install  
Position the Door (v) so the holes in the Hinge Plate (m) line up with the front pair of holes in the Side Panel (s,t). Insert a Hinge Plate  
Screw (k) through the Hinge Plate and thread it into each hole in the Side Panel. Tighten with a Phillips screw driver. Repeat process so  
each Hinge Assembly is secured. See Diagram 9 for assistance.  
Detailed View  
Diagram 9  
s
v
m
k
 
Step 10: Add Mid Shelves  
Thread a Shelf Pin (e) into the desired location in the Side Panels (s,t). For each shelf, four Shelf Pins will be required. Insert each Mid  
Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia-  
gram 10 for assistance.  
Note: Diagram 10 is a Back View.  
Diagram 10  
Detailed View  
s
r
t
wood strip  
e
Step 11: Add Back Panel  
Position the Back Panel (u) up against the assembly and thread a Wood Screw (f) through it and into the Back Stretcher (p). Repeat pro-  
cess until the Back Panel is secured with four Wood Screws. Tighten each with a Phillips screw driver. See Diagram 11 for assistance.  
Note: Sanus recommends placing components and installing all cables/wires before putting the Back Panel on.  
Detailed View  
Diagram 11  
u
p
f
 
Step 12: Hinge Adjustment for small Door  
Each hinge Assembly is adjustable in multiple directions. See Diagram 12 for assistance.  
Diagram 12  
Side Adjustment  
Depth Adjustment  
Height Adjustment  
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05  
 

Pyramid Car Audio Car Speaker PW10290 User Guide
RCA MP3 Player TC1601 User Guide
Runco CRT Television DTV 1200 User Guide
Samsung Car Video System 305T User Guide
Samsung Cell Phone 101 User Guide
Samsung Washer Dryer DC68 02040A 01 User Guide
Sanitaire Vacuum Cleaner SC9180A User Guide
Sanyo Battery Charger ML414 User Guide
Sanyo VCR SRC 800A User Guide
Senco Nail Gun FinishPro 32 User Guide