Sanus Systems Indoor Furnishings PFV59S User Guide

PLATINUM FURNITURE  
MODEL PFV59s - Digital TV Stand  
Assembly Instructions  
BUS5306  
Congratulations and thank you for purchasing your new Sanus  
Platinum Furniture Product. If you have any questions regarding  
this or any other Sanus product, please contact our customer  
not necessary to contact the retailer with any questions or  
problems, as parts can be sent directly to you  
We recommend that the unit is assembled on a soft surface  
such as carpet. Please record your serial number in the space  
provided below and retain this manual for future reference.  
Serial No  
This unit was manufactured using ISO 9000 certified systems.  
For improvement purposes, design and specifications are subject to  
change without notice.  
Please follow these assembly instructions. This will save you  
time, make assembly easier and prevent possible damage to  
your new Digital TV Stand. Assistance may be required for  
some assembly procedures. Correct assembly is your  
responsibility.  
 
Bump-on  
P840022 x 18  
 
B
Front edge  
Glide (gray/black)  
Back edge  
x 6  
Base (underside)  
Fasten 6 glides to the base as shown.  
Note that there are 3 gray and 3 black glides. Use gray glides at front of the base if the stand is going to  
be placed on a light colored floor. Use Black glides at the front if the stand is going to be placed on a  
dark colored floor.  
Left front panel  
Large wooden dowels x 4  
Right front panel  
x 6  
Screw 3 connector rods into holes in left and right front panels as indicated above.  
Press fit 2 large wooden dowels into large holes in left and right panels as shown.  
 
Left side panel  
Right side panel  
Small wooden dowels  
x 12  
Press fit small wooden dowels into left and right sides as shown above.  
Right side panel  
Left side panel  
x 12  
Insert cams into large holes in left and right sides as shown.  
Make sure arrows on the cams point towards the corresponding cam holes along the edges of the panels.  
 
Back  
x 4  
Screw 4 connector rods into holes indicated in back panel.  
Base  
x 4  
x 2  
Screw 4 connector rods into holes in the base as indicated above.  
Insert 2 cams into large holes in the base as shown above.  
 
Left side panel  
Right side panel  
Cable duct  
Press fit the sides to the back as shown above. Turn the cams clockwise to tighten.  
Press fit 4 cable ducts into large holes in the back as shown.  
Assistance may be needed for this step.  
Press fit the sides and back assembly onto the base as shown. Turn the cams clockwise to tighten.  
 
C
x 5  
Fasten the back to the base as shown above.  
x 2  
D
Long rail  
x 2  
Assistance may be needed for this step.  
Hold the long rail in between the sides as illustrated.  
Insert the black barrel nuts into the holes in the long rail.  
Ensure the holes in the sides are aligned with the holes in the long rail.  
Fasten the sides to the long rail as shown.  
 
Press fit the front panels to the sides and base as shown.  
Turn the cams clockwise to tighten.  
Adjusting screw x 4  
Thin side  
Slide thin sides down slots in front panels and back, ensuring silver surfaces face out.  
Screw each adjusting screw into sides by half of it's visible threaded length, then once this is  
done, tighten all 4 Adjusting screws fully into sides.  
 
Steel bracket  
Fit the long steel bracket into the rebate in the long rail and in the grooves in the sides as shown above.  
Ensure the bracket is equally distanced from the sides on both ends.  
A
x 5  
Once the bracket is adjusted in the sides, fasten it to the long rail using the screws shown above.  
It is important that you hold the long rail against the steel bracket as you tighten the screws.  
 
Bump-on(self adhesive)  
x 18  
Attach 18 bump-ons to top surface of the back, sides, front rails, and steel bracket where shown above.  
Assistance may be needed for this step.  
When placing the glass top on the unit, pay attention to the following tips:  
* Ensure painted side is facing down.  
* Back edge of the glass top must be flush with the back panel.  
* Glass top's overhang at the left side must match that of the right side.  
* Lift the glass when repositioning it, do not drag it as it could damage your glass.  
Back edge of the glass top is flush with back panel.  
Front edge  
Above is the top view of the cabinet, indicating where the glass top should rest on the cabinet.  
 
A
x 4  
Fasten the angle brackets to the back as shown above.  
Note - the angle brackets are essential for the strength of the stand.  
Assistance will be needed for this step.  
x 6  
Insert 2 shelf pins into the bottom holes in the right side. Place a piece of polystyrene (from the pack) onto  
the base as shown above (Alternatively you could use a soft rag). Tilt the glass to one side and rest it on top  
of the polystyrene.Then carefully push the glass inside the cabinet and rest the right side on the shelf pins.  
Then raise the left side of the glass up and insert the remaining of the shelf pins into the left side and back.  
Lower the glass onto the shelf pins.  
NOTE: We recommend that all contents stored in or on this item of furniture be removed before shifting it. The  
manufacturers will not be held liable for damage caused when furniture is shifted without first removing its contents.  
If furniture is shifted we recommend that it is lifted not dragged.  
 

Radio Shack Microwave Oven 63 1523 User Guide
RedMax Edger HEZ2500S User Guide
Remington Electric Shaver WDF 5000 User Guide
Roland Electronic Keyboard DP 900 User Guide
Rose electronic Network Card CrystalView User Guide
Samsung DVD VCR Combo CHT 420 User Guide
Samsung Microwave Oven SMH6140WB User Guide
Samsung Refrigerator RF197ACBP User Guide
Schumacher Battery Charger SE 520MA User Guide
Schumacher Battery Charger SF 125A User Guide