Sanus Systems TV Mount XAS1A User Guide

XAS1A  
(6901-100148 <01>)  
Thank you for choosing the Sanus Systems XAS1A. The XAS1A is designed to mount speakers on each side of a  
VMDD26 VisionMount full motion TV mount.The XAS1A will support speakers weighing up to 11 kg (25 lbs.) each.  
CauTION  
Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may  
cause property damage or personal injury. If you do not understand these directions, or have doubts about  
the safety of the installation, contact Sanus Systems Customer Service or call a qualified contractor. Sanus  
Systems is not liable for damage or injury caused by incorrect mounting, assembly, or use.  
warNINg  
This product contains small items that could be a choking hazard if swallowed. Keep these items away  
from young children!  
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA  
 
1: Preparation  
1- 1: New Installations  
If you have purchased a VMDD26 VisionMount™ Full Motion Mount, but have not installed it, begin by following the large  
VMDD26 installation instructions. Replace Cross Tube Installation with Step 2: Cross Tube Installation of the XAS1A instructions.  
When completed, refer back to this Instruction manual, starting at Step 3: Install Extension Tubes.  
1- 2: Existing Installations  
NOTE  
All graphics in this section are generic and are only used to illustrate a procedure.  
[25]  
Disconnect all electrical connections  
and release all cables from any cable tie  
downs. Remove the safety bolt [a] as  
shown.  
[a]  
Lift the TV and arm assembly [B] off  
the wall plate [C] as shown Lean the  
assembly against a wall or other vertical  
surface.  
[B]  
HEAVY! You will need assistance with this step.  
[C]  
[D]  
[F]  
[E]  
Using an Allen Key, loosen the eight vise  
assemblies [D]. Remove the lower cross  
tube [E]; then, remove the upper cross  
tube [F] as shown.  
[D]  
6901-100148 <01>  
 
2: Cross Tube Installation  
[25]  
[02]  
[J]  
Slide the cross tubes [02] into the first monitor bracket  
[g], through the arm assembly [H] and then through  
the second monitor bracket [J]. Center the cross tubes  
on the back of the TV. Using the Allen Key, tighten the  
six vise assemblies until the cross tubes no longer  
rotate.  
[G]  
[02]  
[H]  
Attach the TV and arm assembly to the wall plate  
according to the instructions provided with the  
VMDD26 Full Motion Mount.  
HEAVY! You will need assistance with this step.  
NOTE  
If you no longer have your VMDD26 Installation  
Sanus Systems Customer Service.  
3: Install Extension Tubes  
[02]  
[03]  
Slide the four extension tubes [03] (felt end  
first) into the cross tubes [02].  
[03]  
[03]  
[03]  
[02]  
6901-100148 <01>  
 
4: Install Threaded Tube Clamp & Clamp Knob  
Slide the threaded tube clamps [05] onto the extension  
tubes [03], aligning the notches in the threaded tube  
clamp and cross tubes [02].  
Snap the threaded tube clamps onto the cross tubes.  
Thread a clamp knob [04] onto each threaded tube  
clamp [05]. Do not tighten at this time.  
[02]  
[03]  
[06]  
[05]  
[02]  
[03]  
[06]  
[05]  
5: Secure Vise assemblies to Brackets  
[04]  
[07]  
[22]  
[01]  
4x  
NOTE  
Do not overtighten the nut [22]. The vise assembly  
[04] must rotate freely around the carriage bolt [07].  
6901-100148 <01>  
 
6: attach Speaker Brackets  
[25]  
NOTE  
Slide the speaker brackets [01] into the extension tubes [03].  
Use the Allen key to tighten the four vise assemblies [04] until  
the speaker brackets do not slide on the extension tubes.  
Maximum extension of the cross tubes is 162 cm  
(64 in.). Do not exceed the maximum extension.  
[03]  
[01]  
[04]  
[03]  
6901-100148 <01>  
 
7: attach Speakers  
7 - 1: attach Speakers using Threaded Fasteners  
[03]  
[03]  
[08] - [13]  
Determine the thread of the fastener required by threading each  
size fastener into the back of the speaker. Stop immediately if  
you encounter any resistance. Choose the correct thread size and  
fastener length for your speakers. If using M4 fasteners, [12] or  
[13], be sure to install the lock washer [20].  
The speaker wires may be routed to the speaker terminals  
through the extension tubes [03]. Refer to the instructions  
provided with the large VisionMount™ Full Motion Mount for  
routing speaker wires.  
CauTION  
Disconnect the speaker wire from the receiver or amplifier when you route it through  
the upper or lower extension tubes [03] to avoid damage to the speakers, amplifier, or  
receiver.  
6901-100148 <01>  
 
7 - 2: attach Speakers using Hex Studs  
[14], [15]  
[03]  
[23]  
Choose the correct fastener length, [14] or [15] for your speakers.  
The speaker wires may be routed to the speaker terminals  
through the extension tubes [03]. Refer to the instructions  
provided with the large VisionMount™ Full Motion Mount for  
routing speaker wires.  
CauTION  
Disconnect the speaker wire from the receiver or amplifier when you route it through  
the upper or lower extension tubes [03] to avoid damage to the speakers, amplifier, or  
receiver.  
CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, “CSAV”), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein  
covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to  
change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy,  
completeness or sufficiency of the information contained in this document.  
6901-100148 <01>  
 

Radio Shack Cordless Telephone 43 3548 User Guide
Ratoc Systems Network Card REX CFU2 User Guide
RCA Home Theater System RTS202 User Guide
RCA Telephone 27930 31 User Guide
Russell Hobbs Coffeemaker 10444 User Guide
Samson Stereo Amplifier Acoustic User Guide
Samsung All in One Printer SCX4521F User Guide
Sanyo Battery Charger N 4000DL User Guide
Seagate Computer Drive 3000LS User Guide
Sennheiser Headphones HD 25 13 User Guide